- #1 [wah1080], 21-07-05 08:56
- #2 [alexanderkoo], 21-07-05 09:04I believe that very few C-fu's are having interest on small job. They are indulged in window inspection and repair. Daily routine, just replace rivets with high reward. Being pampered for low skill. Better replace the glass by acrylic sheet of same thickness. Otherwise, it can break.
There is exemption for village house of 3 storey high, no need for window inspection. Possibly, similar for repair work. Still need to check integrity of rivets by your own. Mine were self-taping screws.
Aluminium sheet is also fine but hard to core the openings. For acrylic sheet, can ask the shop to do so. I modify my AC but still using plastic casing, easier to work with.
最後修改時間: 2021-07-05 09:13:02 - #3 [new68u], 21-07-05 09:05如果係我會買塊鋁板開定抽氣扇洞同5吋喉洞,然後拆抽氣扇,拆玻璃,裝鋁板,裝抽氣扇裝喉。
-
- #4 [V.C], 21-07-05 09:10要揾師傅會拆開鋁框攞塊玻璃出嚟,跟住度好尺寸界玻璃再裝返上去,工序消耗時間。
- #5 [wah1080], 21-07-05 09:16#3
請教如你所說拆玻璃,使唔使將成個鋁窗拆落來呢? 呢種鋁窗如果成個拆出來,好似要拆除同安裝窩釘. 我無經驗同無工具做得到. 不過拆同裝抽氣扇我應該應付得到的.
最後修改時間: 2021-07-05 09:18:13 - #6 [alexanderkoo], 21-07-05 09:16Very few c- Fu can cut round openings in situ. Need to take to glass shop. So, better prepare one in advance. But how without taking down?
Two extraction devices, competing for air if used at the same time. Can use cooking range alone(inclined type is better if using induction cooker) and open the kitchen door and living room window for fresh air intake. To complete air circulation path.
最後修改時間: 2021-07-05 09:23:40 - #7 [沉默的膏蟹], 21-07-05 09:23電工師傅裝抽氣扇會幫你換埋玻璃同開窿,裝抽氣扇二、三百,換玻璃二、三百, 裝抽氣扇外開多個窿未必收你錢。
- #8 [ckyj], 21-07-05 09:28塊玻璃再開窿好大機會會裂
- #9 [ckyj], 21-07-05 09:30塊玻璃好大機會會裂
- #10 [V.C], 21-07-05 09:30用刀片清理玻璃膠,用薄頭一字批攝入條罅將上下兩條45度角鋁邊拆落嚟(佢哋負責撐住左右兩邊),左右嗰兩條鋁邊才可以拆埋,塊玻璃就可以攞出。
最後修改時間: 2021-07-05 09:38:27 - #12 [0925], 21-07-05 09:46#3 x 2
改為一個抽氣扇加多一個5寸排氣喉開玻璃和亞加力都好易爛,度好尺寸劃圖標示抽氣扇和5寸排氣喉孔位后揾淘寶供應開塊 3mm 厚鋁板 + 開孔 運落來自己 DIY 或找裝修/電工師傅代工。
最後修改時間: 2021-07-05 09:52:38 - #13 [alexanderkoo], 21-07-05 09:46DIY is convenient but not in line with Ordinance, unless there is exemption for low rise building as said.
If I remember correctly, should remove the vertical angles first which lock the horizontal ones.
最後修改時間: 2021-07-05 09:49:09 - #14 [wah1080], 21-07-05 09:51#10
按你的說法,即係唔需要成個鋁窗拆出來. 只要响室內先將鋁窗的黑色玻璃膠清除掉, 再將上下,左右四條鋁邊拆走, 就可以將成塊玻璃由前面攞出來. 對嗎? - #15 [V.C], 21-07-05 10:14對!
- #16 [learn], 21-07-05 10:25C兄,
你還要伸手出窗外界開"室外"的玻璃膠才能在"室內"取出玻璃的。
之後裝新已開好窿的玻璃時,也要伸手出窗外唧玻璃膠,才能密封玻璃,這個會比較難。
玻璃界2個窿是高難度動作,-般用手開都實難,最好去大玻璃廠如藝華丶冠華訂。 - #17 [new68u], 21-07-05 10:45
- #18 [Richardw], 21-07-05 11:02#3, 建議的方法是最可取,好過拆舊換新玻璃,原因係新玻璃多了很多駁位需要吱膠。
唯一再要考慮係究竟保留個窗掩,top tung sash 還是拆走窗掩,這個則事乎客人要求。 - #19 [wah1080], 21-07-05 11:12多謝#16提醒. 要再睇下如何清除窗外的玻璃膠,可能真係有D難度.
我打算開兩個孔嘅諗法係見到對面單位都係咁做. 都係用玻璃的.
所以我無諗過用鋁板代替玻璃.
#17你安裝浴室寶係用鋁板? 幅圖睇得唔係好清楚. - #20 [new68u], 21-07-05 11:22#19 係, 條link#14嗰張就係銀色鋁板.
- #21 [沉默的膏蟹], 21-07-05 11:30出po問得呢個問題真係唔建議DIY, 手工上唔難,但安全上對一個未學過冇經驗又唔齊工具既人會有d難。
- 下一頁 (1 of 2)
- 返回 ...
請問宜家法例係咪要由有屋宇署註冊為認可資格人士來做呢?
呢D小工程, 我應該係去搵一般五金水電工程公司做, 定係去鋁窗工程公司, 定係去專做玻璃嘅店鋪呢?
謝謝
最後修改時間: 2021-07-05 08:57:15