- #41 [alexanderkoo], 23-01-25 08:42
- #42 [0925], 23-01-25 10:09用咗30年
最後修改時間: 2023-01-25 10:09:27 - #43 [S.Chan], 23-01-25 13:05耐到都唔得,三十年左右.
-
- #44 [0925], 23-01-25 14:31
- #45 [0925], 23-01-25 14:57https://item.taobao.com/item.htm?spm=a230r.1.14.16.111753fbJZ40pr&id=634438399279&ns=1&abbucket=12#detail
可惜唔係 brushless 和唔係綠式系列的(我有個 Dewalt battery adapter for GREEN series)
最後修改時間: 2023-01-25 14:58:30 - #46 [0925], 23-01-25 15:23用開 cordless 又冇 jigsaw 的可考慮
最後修改時間: 2023-01-25 15:23:58 - #47 [0925], 23-01-25 20:484 mm² 紅、黑線和地線係捌幾年買回來拉線入浴室駁 4000W 儲水式電熱水爐用剩,燈喉配件係二千年大碌國買落來至今用剩。
最後修改時間: 2023-01-25 20:49:01 - #48 [R939], 23-01-25 22:58
- #49 [0925], 23-01-26 00:31
- #50 [0925], 23-01-30 12:45
最後修改時間: 2023-01-30 12:45:27 - #51 [alexanderkoo], 23-01-30 16:13Tested the whole installation to earth with hi-fi unplugged, 250V DC, 10 Mohm, not bad. Washer and water heater, better than 1000Mohm, 500V.
Today, wired a 3C 2.5 sq.mm from main board to a twin socket for new AC and PC. Originally, one socket for two AC's, used in alternation, bad idea.
最後修改時間: 2023-01-30 16:13:18 - #52 [alexanderkoo], 23-01-30 16:21Vintage sharp projector could power up, display of menu but having picture once for a while. Took out the PC board and motherboard(RHS)but at my wit's end after checking the caps. Maybe the processor having dried joints, needs reballing. Re-assemble, all screws were there. Give away to re-seller.
最後修改時間: 2023-01-30 16:21:44 - #53 [0925], 23-02-01 16:59而家唔想用啲質量差的油壓鑽咀,每次都多花幾秒鐘來鑽一個牆窿
Cut 短佢攞個頭打膠塞入牆窿內
最後修改時間: 2023-02-01 17:01:24 - #54 [0925], 23-02-02 11:00#53 + 1
同樣係 cheap 鷄鑽咀,#53 支 Dewalt 硬過呢支 Dunsk
最後修改時間: 2023-02-02 11:02:11 - #55 [0925], 23-02-02 16:39#53 + 2
同樣係 cheap 鷄鑽咀, Ezarc 硬過 Dewalt
最後修改時間: 2023-02-02 16:40:41 - #56 [泰tai], 23-02-02 23:25#53 用鑽咀改,大鎚揼會唔會飛鋼
- #57 [0925], 23-02-03 00:32大鎚揼會唔會飛鋼<
有 centre spot punch,啲鑽咀用來放喺啲親戚屋企,將來幫他們做家居維修鑽牆打孔定位用,已每個家庭送一把油壓鑽。
最後修改時間: 2023-02-03 00:32:59 - #58 [0925], 23-02-03 11:13
- #59 [0925], 23-02-04 18:29俾兒子捉咗去幫佢公司拉電,整咗約五份一
最後修改時間: 2023-02-04 18:29:49 - #60 [0925], 23-02-05 10:25
- 下一頁 (3 of 26)
- 返回 ...
Re-installed a few ssd's(including an old windows 7, left idling for a few years) with Windows 10, upgraded one to Windows 11. One ssd having MBR problem, used Seatool for erasing(back to factory status) AKA low level formatting/zero filling. So don't dump despite having glitches. Cloning a SSD to a larger one, don't start up at the same time, otherwise, crash due to same configuration. Image recovery using Easeus Todo freeware. 512G Teamgroup SATA SSD is only HK 200, Bought two. Good buy. NVME M2 512g ones, bought two. 1 T is a lot expensive.
最後修改時間: 2023-01-25 08:44:21