- #41 [一縷輕煙], 20-06-15 19:58
- #42 [phil.ng], 20-06-15 21:55>>>此方法小弟不建議,很大機會全堵,即冇得救
有機會丶樓主要講講煮食習慣丶多廢油丶動物油???
平時有冇用熱水洗?
是否每次都用大量洗潔精?
看來1需用高壓特別通喉頭
本屋苑每年做兩次用高壓水通
最後修改時間: 2020-06-15 21:57:00 - #43 [phil.ng], 20-06-15 21:59全堵丶如只是油丶可試cut 頭丶在我的#32
現今鬼子佬好多通喉工具丶要多加留意
香港師傅丶唉!好多都冇先進工具
香港人的不幸!
最後修改時間: 2020-06-15 22:03:12 -
- #44 [phil.ng], 20-06-15 22:10.
- #45 [phil.ng], 20-06-15 22:11.
- #46 [phil.ng], 20-06-15 22:11.
- #47 [lilaclee], 20-06-15 22:17成日驚伸左條通渠wire入去, kick住出唔返來咪大鑊?
- #48 [phil.ng], 20-06-15 23:13轉迅夠快丶拉出不難
- #49 [singkee1], 20-06-15 23:32試左飛魚牌未?
- #50 [CS168], 20-06-15 23:38
路過一問,厨房洗碗盤,凍水來水慢,
有似痾尿咁。
原因濾水炭芯之前太耐冇換,有黑色碎粒可能塞著
銅喉接位,因經常拆水喉咀隔片內見到微細滤水芯黑色炭芯棵粒。 - #51 [CS168], 20-06-15 23:41
濾水隔器濾芯己拆走一年了,thanks!! - #52 [ronnieng], 20-06-15 23:59以往用金钃蛇由洗碗盤口入,但轉極都去唔到大喉管。最後改由直喉入就易通好多。下面借圖示意。
- #53 [alexanderkoo], 20-06-16 08:46The demo is fine, smooth bends. In reality, didn't work so don't waste your money. Got two. TV coaxial cable is very good with frayed end, braided wire hence flexibility but won't fold by itself. In industry, people use high pressure water to clean or a pigging system with a through wire and metal head.
Better not use flying fish "opener", might attack cast iron pipe, leakage after a few years.
Today, I would commission the newly modified kitchen sink basket and plumbing system. 50mm pipe but not all way through.
最後修改時間: 2020-06-16 08:52:28 - #54 [alexanderkoo], 20-06-17 15:00The kitchen sink drainage is working good, with 90% pipe replaced. Would have been better if I could enlarge through wall opening to 50mm. Most difficult part was drilling 90mm hole on existing stainless steel basin to accommodate the basket. Enlarging existing hole is more difficult(no centre hole to align the cutting tool, though appears simple)than new opening.(so plugged the old opening afterwards) Must be slow speed, don't press, on and off, with coolant and lubricant. Too much heating would harden stainless steel so more difficult to drill. My wife thought that I would fail.(kind of motivation, in negative sense) Complete sink replacement would be a big job since sides filled with lots of cement.
最後修改時間: 2020-06-17 15:02:06 - #55 [0925], 20-06-17 15:33
- #56 [phil.ng], 20-06-18 11:24失蹤!
- #57 [alexanderkoo], 20-06-18 12:19#55 got the same, RMB 23. Should be close to 85mm when the basket arrived and having exact measurement. 90mm was my guess based on 110mm top measurement and 10mm thickness for flange. Diameter varies with different models. Too small drill diameter is useless.
Can ask someone to enlarge the concrete opening from 37 to 50 mm, got Worx hammer drill with chiselling. But hole would be irregular. Coring would be more nice but diamond tool is overpriced. Got primitive tool for coring brick wall, can drill 9 nos. 6mm holes around the circumference, much easier. The external side is high level so working with heavy tool is a bit difficult.
最後修改時間: 2020-06-18 12:22:25 - #58 [alexanderkoo], 20-06-18 14:00Got this 327D(with suffix D, must need chiselling function as well ). Used once to drill 5/16" hole, simply hot knife cutting butter. (a lot powerful than my vintage Metabo drill or newer Ryobi cordless hammer drill) Good buy but quite heavy, a bit of vibration. Size of piston would matter. Comes with lots of square drills/chisels. Should be the first drill to possess if one has got NONE. Good enough for plumbing installation, 3/4" copper pipe inlet.(outgoing 1/2" should use hot water pipe for throughout for thicker PVC sleeve)
https://detail.tmall.com/item.htm?spm=a1z10.5-b-s.w4011-14939626795.48.2df67573RH6L3P&id=544586278127&rn=ee59ab20a1c4061d2375d2953c430c03&abbucket=1
最後修改時間: 2020-06-18 14:04:28 - #59 [S.Chan], 20-06-18 14:27開大星盤個窿使唔使壓番個凹位裝個去水器。
- #60 [alexanderkoo], 20-06-18 15:35You can't so there must be 2mm water level remnant after mod. (no other choice) So, better buy a new basin with basket if existing one can be easily demolished. (av, RMB 120) But situation has been greatly improved, needed pumping every time before mod. Finer strainer, hence small debris into plumbing, fewer clogging.
UPVC pipe here. Free shipping in Mainland for order >RMB 29. 40mm pipe, only RMB 5/m.(in 1m length for easy shipment) Need to buy the pipe as well, measured in outside dia. as different from local ones.(ID) So, only good for new work. Can insert and glue a few inches of Taobao pipe onto existing ones(1.5 in. glued length would be good enough), then can use Taobao cheap fittings throughout. 50mm T, Taobao , RMB 1.85 but local Lamma island price, $12.(Yin Hing price?) $15 materials from Taobao, can modify a pipe with T or bends.(must be accessible) No leakage, due to low pressure. Not happy, can put some bond steel around the pipe for water tightness and mechanical strength.
https://detail.tmall.com/item.htm?spm=a1z10.5-b-s.w4011-22175006656.57.2e13523fq4AiUB&id=587154460718&rn=1032da7b26feed176a6afc17ac2fe8fa&abbucket=1&skuId=3997414169176
Can find complete sink assembly here. Two types, benchtop, the other below bench. Usually, the former is chosen, fewer chance of leakage.
https://item.taobao.com/item.htm?spm=a230r.1.0.0.44d0523cDMsFRd&id=609242895901&ns=1#detail
最後修改時間: 2020-06-18 15:43:34 - 下一頁 (3 of 15)
- 返回 ...
小弟做飲食業,對抗油積30多年,(塞)此字其實可以由小至無限大,亦即嚴重程度,自己通到好講彩數,代表並不嚴重
phil大哥,此方法小弟不建議,很大機會全堵,即冇得救