- #1 [cat121], 22-11-15 08:37
- #2 [羅密歐], 22-11-15 09:12
- #3 [cat121], 22-11-15 09:19前輩!多謝你的資料
但其實本人為新手,不太看得明白
應該不用拆機,是在接線上更改
可否給多些指引 -
- #4 [羅密歐], 22-11-15 09:39不用拆開機箱。
你需要的是bridge mode adaptor,它可以用電子零件砌成,也可以用分相牛來代替。
如果你只有一對405,沒有bridge mode adaptor,你是不能簡單地透過所謂[設定]/[setting],將系統變成bridge mode的。Quad 405並無這個功能。 - #5 [hahayanyan], 22-11-15 09:53Super nice instructions
羅密歐 master Thx you
將來 可能會用上
最後修改時間: 2022-11-15 09:53:49 - #6 [shungyan], 22-11-15 10:04橋接好似多咗兩粒可變電阻去match 左右output, 請問如果match得唔準會點呢? 同埋點先match得準呢?
- #7 [羅密歐], 22-11-15 10:14非也。
橋接,即[outputs wired in series],要附圖中那件器材的輔助才可以。不過我從未見過,是否存在世上也未可知。
當然也不一定非用Quad所指定的不可,其他品牌也偶見有類似產品的。
最後修改時間: 2022-11-15 10:20:27 - #8 [羅密歐], 22-11-15 10:21就是這件器材。
- #9 [rcywong], 22-11-15 10:22Following the Quad's instructions, it is not difficult to diy a small box adaptor for each 405 power amp. Remained that you have to determine the configuration of parallel or inseries. I had played with the parallel connection in the past.
- #10 [hahayanyan], 22-11-15 10:27Quad vintage solidstate power amp
如果不介意 off topic a little bit
有冇啲有經驗嘅人可以分享下 不同型號的聲音 and hifi 表現特色?
甚至乎 Bridge mode vs standard mode etc..
Thx you
Haha - #11 [bambino], 22-11-15 10:30羅師傅, 樓主的喇叭是4ohm,所以bridging方式是parallel. 相信不一定要bridge mode adaptor或分相牛. 如這pdf所講,用隻5K ohm potentiometer將(同一部amp內)左右channel訊號調教到一樣就可以 (好似balance掣咁). 同一部amp左右channel outputs connected in parallel.
最後修改時間: 2022-11-15 10:32:02 - #12 [羅密歐], 22-11-15 10:36我對此的認知是,bridge就是outputs connect in series串聯。Parallel就是並聯。與喇叭阻抗,無必然的關係。
- #13 [孟波], 22-11-15 10:44通常一部amp,橋接前最佳喇叭負載是4-16 ohm的話,橋接後最低負載阻抗會由4 ohm變成8ohm,即8至16ohm(高過16 ohm喇叭冇乜,所以唔寫32ohm),最低阻抗負荷能力減半。
最後修改時間: 2022-11-15 10:46:55 - #14 [bambino], 22-11-15 10:544 ohm load .....
最後修改時間: 2022-11-15 10:55:03 - #15 [bambino], 22-11-15 10:56最重要一句.....
最後修改時間: 2022-11-15 10:58:15 - #16 [孟波], 22-11-15 11:09sony and marantz, not Quad.
- #17 [孟波], 22-11-15 11:17As well as Philips LHH.....
- #18 [rcywong], 22-11-15 11:43Quad 405, if you need to connect with 10~16 Ohm speaker, you need an input transformer 1:1, as wired in series, referring to Quad service manual "page 26".
*Remember 405 output is phase Inverted.You need to reverse the speaker wires polarity.
最後修改時間: 2022-11-15 11:56:27 - #19 [bambino], 22-11-15 11:57孟波兄, #16/17 BTL bridging方式係串聯(in Series),所以output impedance double. 當bridging方式係並聯(in Parallel)時候, output impedance就是half.
Quad 405 output impedance.....
相信廠用8ohm做reference. 當用4ohm load (speaker)時候就建議兩個channels connected in parallel
最後修改時間: 2022-11-15 12:03:57 - #20 [羅密歐], 22-11-15 12:05當並聯(in Parallel)的時候,就不該叫bridging了。
BTL的B,就是Bridge,就是串聯。既然是串聯,就不會是並聯。
串聯和並聯,是電學中的標準用語,有明確清晰定義。 - 下一頁 (1 of 2)
- 返回 ...
喇叭建議用4ohm及比較大食
請教各位高手
Quad 新手求救