All lenco user..

If u are looking for a cheap arm lifting device..

This is what I am using.. A cheap taobao lifter and some simple tweaks.. Bending on that activation arm in order to fit in the the space.. Etc..

Not many lifter fit into that tiny space..

So nice.. It does take more than a few minutes to get it right


Haha





最後修改時間: 2022-03-03 14:42:33

Happy..

Feeling good.. 係心理因素 about this chassis


Feeling good.. 絕對唔係心理因素.. About the rewire.. Haha


摩打轉動有噪音.between idler and the motor shaft. However 幫個摩打三條彈弓鬆一鬆骨之後就沒有... 即係代表those motor spring.. May be a bit old or aging...


請問各位lenco 用家 對嗰三條摩打避震彈弓更換 any sharing?

The add on arm may be better to locate 15mm to the back.. With better angle.. Etc



最後修改時間: 2022-03-03 14:14:39

Happy happy...

Funny loud noise and hum all gone...

Haha

For all lenco user... It is really not that hard to rewire this arm.. Apply heat.. Get the right tool to remove the locator pin and apply heat... Use a round pin insert to the locator hole and push the connector out... A little bit.. And if having a little bit of luck.. Connector goes out a little bit and having a thin edge to grip and pulllllll


I having a thermal control heat gun.. (I suposoe it is+/-20 degree C from this cheap things..) at 350 degree C over the arm collar a few circle.. Less than 30 sec in total..


I would not do it.. If the cable is still fine


Haha



最後修改時間: 2022-03-02 18:53:17

Haha conduct.. And no shorted..
如果 專心一點, should be easily done within 2 hours..
Haha



最後修改時間: 2022-03-02 15:50:17

Goood


Haha

Lalaalaa

Loosely braided them


Haha

Haha exciting...

Haha

Find those silver wire.. 50cm is more than enough..

Target heat around the collar area..

And I use a very fine nail clipper to grid the point and after heated.. It may s quite easy to pull off.. (last time... me I did not add heat.. And was so difficult)

Shall get. Some measurement and 3D print another pcs for another lenco arm... Haha

Next.. Find my arm cable... I have some...



最後修改時間: 2022-03-02 12:56:10

Haha

Done.. Haha add heat... Add heat.. 350 degree

Seem there was somework was done before me.. HaHa



最後修改時間: 2022-03-02 12:54:30

I have read almost all of the thread about rewire this.. Haha

They were some super easy pull off.. They also many of them same as me.. Total failure..


Guess I have to make a move now.. I try after some fresh air. M

Remember u mentioned.. U heat that up


There were people able to do it.. Without pulling the pin out too

Haha

最後修改時間: 2022-03-02 11:29:00

yes i read that many time.....thxxxxxxxxxxxxxxxxxxx

and i have / had difficuty on getting the connector out............

which was your prefer way to get that out ?


haha

最後修改時間: 2022-03-02 10:08:08

Hi hi hi HA HA HA........

I am here, right here right now.

Have you seen this thread?

https://www.lencoheaven.net/forum/index.php?topic=8601.0

hihihi fotheringayfotheringayfotheringayfotheringayfotheringayfotheringay

happy to offer me some useful tip for rewiring the Lenco arm ＞ last time...i broke..it , and i have rewire this one.. ...

thxxxxxxxxxxxxxxxxx


hahaa

Haah.. The chassis is kind of flat and straight.. With a bottom frame embedded within the top frame.

Thin and floating...

Tear off the red wire again.. Haha

Haha.. Fun

I bought a super bearing several years ago for my Lenco project which never materialised, if any C Hing interested can PM me.

A sub chassis...

Haha..

Lazy or not lazy.. Embeds it or just on the surface haha


.

絕對的心理作用真係覺得唔錯 haha haha

The red wire.. Is just disintegrated veery oxide too .. Seem I have to rewire it soon.... I suppose most lenco arm may need rewire..

Hope coming rewire.. I will not break the headshell socket.. Haha

Haha lucky.. Wiring within the arm tube still connected..

And without shorted.. Haha

Last time.. I try to rewire a lenco arm.. And break it.. I. Not ready to rewire this lenco arm yet.. Haha






最後修改時間: 2022-02-28 12:24:52