- #232 [hahayanyan], 21-06-08 12:57Haha
- #231 [hahayanyan], 21-05-22 22:08Haha... It is a lenco.... Haha
- #230 [hahayanyan], 21-05-22 14:34Haha
有一個無聊嘅玩hifi nubby... Haha
High hand.. Brought 2 lenco.. Buy not using it..
Heard that he wants to let's go haha
play lenco laaaaaaaaaaaaaaaaaaaaaaa if u have time... fun and rewardingggggggggggg
最後修改時間: 2021-05-22 14:48:02 -
- #229 [hahayanyan], 21-05-22 10:36Haha if today less lazy.. I add one more tone arm to it
Or rewire the other lenco arm.. Which I broke.. HaHa
Haha
最後修改時間: 2021-05-22 10:38:30 - #228 [hahayanyan], 21-05-13 11:16
haha still working on it....
- #227 [hahayanyan], 21-05-05 16:13Haha still working on it..
Haha - #226 [hahayanyan], 21-04-22 14:252nd layer.. Couple by 3 steel balls at each corner.. Haha
As I have those steel ball bearing around... Why not haha
最後修改時間: 2021-04-22 14:35:27 - #225 [hahayanyan], 21-04-22 13:32Sandwich the base frame and fasten them by screws
Middle layer is mahogany, between ebony - #224 [hahayanyan], 21-04-21 21:10The base frame.. Haha
- #223 [hahayanyan], 21-04-21 21:09Haha.. Carry on tomorrrow
Haha - #222 [hahayanyan], 21-04-21 18:27Upto this moment...
Haha
I thinking.. Should I make a bottom square.. Or just a H frame... Haha
最後修改時間: 2021-04-21 18:33:38 - #221 [hahayanyan], 21-04-21 16:10Having fun
- #220 [hahayanyan], 21-04-16 15:24more wooooooooooooooooooooooood is cominggggggg
haha - #219 [hahayanyan], 21-04-05 15:37Haha
無無聊聊就搞搞佢 haha - #218 [hahayanyan], 21-04-04 15:38
Haha
I think I should make an extantion cable for my little Sony mic.. Haha for correct orientation.. Haha - #217 [hahayanyan], 21-04-04 15:11Some left over ebony.. And why not
Shall take some learning from that..then make something to a sme3009
Haha - #216 [hahayanyan], 21-04-04 15:10Haha just for fun
Haha... Not bad... For less Than. 1 hour
Feel more alive for making something - #215 [hahayanyan], 21-04-03 19:45Some reported 4 mins with new ball and thrust plate
- #214 [hahayanyan], 21-04-03 19:16Haha
. Great finding...
I just clean the whole shaft..etc.. And use 5W/40.... And then 33 to 0 test is 56 sec... And better than 40 sec... Haha
Freaking info to share.. There is an upgrade bearing kit.. At ukp 170...said to have 33 to zero testing... At fxxking... 7 mins... Omg... Hhaha
I better push my engineer.. For Making it for me.. Haha
My sharing over the Facebook lenco group, and some funny response from other too..
have fun
https://m.facebook.com/groups/52429986758/permalink/10157786435006759/
最後修改時間: 2021-04-03 19:25:26 - #213 [hahayanyan], 21-04-03 17:09A lenco user.. From UK.. After he spend some time on rebuilding the shaft.. Etc..
His time from 33.3 to zero was 90 sec
My time.. Is about 40 sec... Haha
Which means.. I am a lazy lenco owner.. Haha
Seem Terry is less lazy Than me... Wonder how's the time from his lenco... Too
Hahaha
最後修改時間: 2021-04-03 17:12:28 - 下一頁 (6 of 17)
- 返回 ...