- #41 [CADiver], 15-03-24 14:57
- #42 [cornercube], 15-03-24 17:15>>#37...intelligent curve tracer三年前一出即買...代客裝機修機,必備之恩物也...
>>#40...勁! X2
---------------------------------------------------------------------
我齋up唔做&唔識做;
Le度d各實戰C Hings 果然 勁!! - #43 [cornercube], 15-03-24 19:59又up下.
PCB diy, 如果taobao買, 最好揾到FR4料;
銅皮厚度 本來越厚越好, 但 自己食, 驚越厚越衰,
估 2盎士(70u厚) 已經OK??
最後修改時間: 2015-03-24 20:15:20 -
- #44 [cornercube], 15-03-24 21:12>>#30...But hv to do at the factory
----------------------------------------
try google:
laser cut hk
see if it can be done (in hk):
http://tinyurl.com/k8wwdxd
最後修改時間: 2015-03-24 21:20:34 - #45 [kslsfz], 15-03-24 21:50用防彈膠做唱盤platter都幾吸引?過都唔知揾乜去切割做machine tooling
In stark contrast the TT-Three Reference platter is light, highly inert and made from Lexan (bullet proof glass or polycarbonate) which has virtually no reflective or resonant storage problems, it weighs less than 900 grams and therefore has ultrafast recovery time, add to that the fact that polycarbonate has one of the highest energy absorption coefficients known to Man and you will see why this is the only proper solution combined with a strong drive system. - #46 [gy2004], 15-03-24 22:53#38 & #39
CADiver Hing
You are one of the crouching tigers & hidden dragons of review 33. Other than the router table and bandsaw machine, I can believe you have CNC machines too. - #47 [CADiver], 15-03-25 12:21
講笑啦師兄, 識禾的人都知禾無料到, 不過佢地末出來踢爆禾車, 但係,禾很學很做,所以請禾啦...
講到CNC其實今日好多師兄放響音響的金錢相比起一台幾本好用的CNC,根本就無得比,實用CNC連一部大廠後級的錢都唔使.但禾亦明大家都地方小,不過又好多師兄都有工廠大廈單位發燒咁呢D又唔成問題囉...
其實好多野都係用手用心做比較rewarding機器只係幫幫忙快小小車...
呢度係車跟塊armboard,雕左亞仔個名,用意係希我死左之後,佢無咁快雕晒的野囉.... - #48 [cornercube], 15-03-25 12:27Wah! laser cutter/engraver 都有.
- #49 [user_aaron], 15-03-25 12:54司機師兄唔知接唔接單嘅呢?
我想刻字。 - #50 [welborne], 15-03-25 13:15係潛水員兄,唔係司機:)
- #51 [CADiver], 15-03-25 15:29師兄, 刻乜,刻係邊度, 刻幾大, 幫得到我一定幫, 但你要自己做個design in Adobe illustrator. 如果要cut through 就要係用條.01point 細缐outline如果係engrave 就唔同,
定位師父叫我做水怪可以咁call我,唔使客氣....
前面介紹過一絛度tonearm 的間尺,其實用來吹皮燒乳鴿仲用得比較多... - #52 [welborne], 15-03-25 15:46水怪兄,你住香港or California?
- #53 [CADiver], 15-03-25 16:16
定位師父叫得我做加州水怪, 緊係住加州多的啦, 唔怕水泈,我帶你地去潛加州凍水... - #54 [cornercube], 15-03-25 19:59
>>#36...音箱做90度角無咁好睇
-----------------------------------------------
or try鋪木皮.
://www.youtube.com/watch?v=FgAxVUabkBg
最後修改時間: 2015-03-25 20:01:49 - #55 [gracejones], 15-03-26 07:22五金 (做鋁/鐵箱) : 大角咀, 新填地街, 廣東道, 山東街 ?
- #56 [welborne], 15-03-27 02:59我想造這個箱
- #57 [daniel-chui], 15-03-27 08:26羅密歐兄,想向你請教,整 intelligent curve tracer和膽 curve tracer,請看PM,謝謝!!
- #58 [kingphilip], 15-03-27 15:19在淘宝淘了一款高轉數,據報(5000一18000Rpm)小切割機!對cut輕型金屬片應該可應付了150人仔未計運費收到后post相比各ching 參考下
- #59 [cornercube], 15-03-27 16:47機箱, 知道taobao有1間賣:
清風机箱taobao
(冇幫趁過)
最後修改時間: 2015-03-27 16:53:19 - #60 [cornercube], 15-03-27 17:24From R33...ATC SCM40重生記............
#53.."".用 REW 和 DAT2 也能找出鴛鴦單元, 由其是買二手喇叭. DIY 朋友 不用再估估下....""
好奇揾到.
http://www.roomeqwizard.com/
最後修改時間: 2015-03-27 17:27:29 - 下一頁 (3 of 7)
- 返回 ...
Have a nice piece of straight solid wood stick. Drill a hole in one end big enough to fit the turntable's spindle. Measure out 8 inch, 9 inch, 12 inch, 16 inch from the hole center and drill a tiny hole at each of the measure big enough for a nail, push a nail through the tiny hole. Now you have a decent accurate ruler to help you set the tone arm location whether is marking the drill hole on the tone arm board or location for where to place the tone arm.