- #21 [cornercube], 15-03-23 19:34
- #22 [welborne], 15-03-23 20:26請教咩係PC? PVC我知
- #23 [cornercube], 15-03-23 20:37up下:
PC> 講誇d叫防彈膠.
去買個陣唔講.
只叫PC.
防彈WOW!! 分分鐘天價咁賣左塊膠.
(估)PC貴過亞加力 3-4成左右, or
from below.
http://tinyurl.com/nfcp7s8
http://tinyurl.com/khmotzk
最後修改時間: 2015-03-23 21:09:03 -
- #24 [eric4448], 15-03-23 21:10請教師兄知吾知道邊度有粗身細size橡根圈賣
- #25 [cornercube], 15-03-23 21:43>>#24...邊度有粗身細size橡根圈
--------------------------------------
le間唔知有無diy橡膠條賣.
(橡膠圈自己整)
http://goo.gl/maps/WtDMf - #26 [eric4448], 15-03-23 21:51吾該c兄、明日去看看
- #27 [cornercube], 15-03-24 08:02diy 擴音機, power管要配對, le件唔知掂唔掂?
自己少整機, 無買.
http://www.eevblog.com/forum/projects/my-intelligent-curve-tracer/ - #28 [kingphilip], 15-03-24 10:47有冇ching可以教路,我想在LP唱盤面板開過唱臂孔,大约要2寸X4寸,佢本身是1.5mm簿鐡板,如果吾拆出黎就咁cut?當然要拆左支臂!有乜工具可以做到?
多謝指教!!! - #29 [cornercube], 15-03-24 10:48try laser cut
- #30 [kingphilip], 15-03-24 11:00But hv to do at the factory
- #31 [cornercube], 15-03-24 11:20//www.youtube.com/watch?v=e3hB1ssQwPg
- #32 [徐福], 15-03-24 11:22如果開圓孔.可以用金剛砂開孔器
- #33 [baker.steven], 15-03-24 11:33.
- #34 [baker.steven], 15-03-24 11:33.
- #35 [baker.steven], 15-03-24 11:34.
- #36 [gy2004], 15-03-24 12:07舊年寄曾經計劃造個音箱, 想買個Router用泥開圓孔, 但睇網上資料話如果唔係熟練人士, 用起上泥會有危險, 所以始終無買到
另外想問下有乜工具可以係木板邊緣開45度斜角, 音箱做90度角無咁好睇 - #37 [羅密歐], 15-03-24 12:34Cornercube兄, intelligent curve tracer三年前一出即買,唔算易用,不過一旦上手,會有好多新發現,邊間D零件堅,邊間吹水唔抹咀,貴野平野有乜分別,一目了然.用過之後,網上/雜誌/論壇好多人講乜野NPN/PNP 5%配對之說,必然有全新體會.連原廠spec sheet,都不可盡信.單係用來試市面上六七種唔同品牌既三腳穩壓IC LM317,都可以玩成日.不足之處係電壓唔高,只有0-36V,用來試高壓大功率管時,未能盡興而矣.我代客裝機修機,必備之恩物也!如果鍾生開發膽用curve tracer,更要飛身去買!我自裝的膽curve tracer,雖然都易用,但測繪一隻膽曲線,要半個鐘呢.
- #38 [CADiver], 15-03-24 13:18Router table is a fantastic machine to have, it can make a lot of things that aren't smooth or join perfectly to become perfectly, it can also smooth out cures. It's my favorite machine even if I don't need to use it every time I do something ....
Making Quad ESL-63 top wood panel. I made some maple, cherry and walnut replacement instead of the original light weighted wood. - #39 [CADiver], 15-03-24 14:40Bandsaw is another almost must have tool, I would almost say, I use this even more than the table saw. You can sitll cut a 45 degree joint with bandsaw if you have a 45 degree stop block. Might not be as smooth and perfect as using table saw but a couple hit at the sander belt, it's just as good as table saw cut.
- #40 [welborne], 15-03-24 14:56勁!陰莖陰莖
- 下一頁 (2 of 7)
- 返回 ...
PC強度最勁.