- #80 [mentos], 15-03-17 11:32我又係KT-90(Jaids orchestra signature)...就黎忍佢唔住..
- #79 [drchan], 15-03-17 10:31One typical push-pull amplifier schematic drawing
最後修改時間: 2015-03-17 10:34:35 - #78 [drchan], 15-03-17 03:20有些朋友問我市面上無數膽機
無線路圖。怎麼調較換膽
好彩膽機線路比較石機簡單得多
經過一佰年來發展
剩下只有幾款常常用的線路和幾十款常用膽
幾千元同遏百萬元的膽機線路都差不多
只是用料的分別
所以我的朋友帶機給我修理或升級
我都通知他們不用擔心線路資料不全的問題 -
- #77 [old8210], 15-03-15 09:58Good thread.
....... - #76 [drchan], 15-03-14 16:52今天早上有位師兄 基哥帶來一部用KT90的Jadis
來找我幫忙改用KT150
一開始未改前開機聽聽
國產KT90膽 非常難聽
一個形容是。削
換上K150 後再聽
立即升一班
然後打開機箱
逐一調較每一只膽的bias
重新再開機
一天光晒
要乜有乜
我很高興看到機主帶著笑容回家
相信這部機可以有排玩 - #75 [old8210], 14-08-12 05:50........
- #74 [ama333], 14-08-11 16:36Dr Chan
Check pm pls.
最後修改時間: 2014-08-11 16:36:26 - #73 [drchan], 14-08-11 13:06Ama333,
It is too difficult to answer your questions without visualise you amp! - #72 [ama333], 14-08-11 12:44Dr Chan
AS quoted by Mercury Magnetic
"The VTO-100 output is a 1700 primary and 5 ohm secondary.
It will handle 2 x KT120’s or KT150’s"
最後修改時間: 2014-08-11 12:45:11 - #71 [ama333], 14-08-11 12:35Dr Chan
Thank you for the offer,very much appreciated.
I just found out from the transformer manufacturer that the VTL 10th anniversary triode can handle k120x2 and k150x2.
Do I still needed to adjust bias if the transformer can handle k120 and k150? and what does k120x2 & k150x2 meant? My amp's is using four k90 now.
最後修改時間: 2014-08-11 12:35:40 - #70 [drchan], 14-08-10 12:38ama333,
如果你還有換胆的困難、
你可以帶你部胆机到我公司
我可以免費幫你微調一下
請用PM與我聯絡
Dr Chan - #69 [drchan], 14-08-08 18:11I think the bias adjustable resistors are installed inside the chassis like Jadis,
- #68 [ama333], 14-08-08 16:11Dr Chan
I have an VTL KT90 10th anniversary Triode amp, there are no manual bias adjustment for the amp. Do you think I can use KT120 & KT150 tubes on my amp?
Thanks
最後修改時間: 2014-08-08 16:11:20 - #67 [kenedward], 14-08-08 15:18Thank you Dr Chan,
However, why do you sell your quad of kt150?
ED - #66 [drchan], 14-08-07 18:36I bought matched quad set on eBay.
About $3,000
including delivery charges.
最後修改時間: 2014-08-07 18:37:01 - #65 [ok1978], 14-08-07 15:02Where I can buy Tung-Sol KT150 in Hong Kong?
- #64 [drchan], 14-08-07 13:57The typical efficience of Pure Class A single ended tube power amp is about 25% and the standby power consumption is 50%; as a result, if 250w power transformer is used in your amp, the maximum continous consumption go up to 200w is the limit, than the pure class A output by any tubes is 25w, and the standy power consumption is 100w plus the tube heaters filament (9w for each KT150)
Whenever you change the power tubes, the first time must be done by manual adjustment, than you will find out any defective tubes. - #63 [kenedward], 14-08-07 10:18Dear Dr Chan,
Thank you very much indeed.
Since the transformer of most chinese kt88 se amps is only 250w, do you think it is good enough for kt150? Most sellers told me that could not support kt150.
Would the auto bias adjustment good enough or do I need manual bias adjustment?
Your precious advice helps us a lot.
Thanks again,
ED - #62 [drchan], 14-08-06 18:09The one pair KT150 with 150w output per channel with bias only 60mA in class AB
The single ended one piece KT150 with 30w output per channel with bias 100mA in class A
400 - 500 w power transformer is ok in both cases. - #61 [kenedward], 14-08-06 17:28Thank you Dr Chan,
However, the power transformer is only 400 - 500w. A real KT150 pp amp might be 700W up. Ppl told me 400w could only handle KT150 SE. Also, do you the normal bias for KT150 SE? Thanks again.
ED - 下一頁 (5 of 8)
- 返回 ...