- #1 [ckhung], 22-05-27 11:00原開孔60mm要變做65mm, 冇鑽床有咩做法好?
- #2 [hahayanyan], 22-05-27 11:04
Pretty way 去淘寶made一塊65mm內徑嘅5mm厚亞加力板 as a template, and then a 喺淘寶買一個 200蚊嘅wood router.withtop bearing bit. 你明白上面講乜你就會知道細節應該點做
將以下嘅木板換成一塊正確嘅 亞加力導向板
U may find a 65mm hole saw.. Too
There are easy way to fix a centre position too
最後修改時間: 2022-05-27 11:18:36 - #3 [hahayanyan], 22-05-27 11:21using this type of router bit..and cost about rmb 30 ( top bearing type )
-
- #4 [ckhung], 22-05-27 11:28謝謝師兄, 非常詳細的解釋. 我剛才都諗到用修邊刀落手, 但未諗到師兄有定位的方法, 相對配合埋定位去做, 成件事便可更加完美了
- #5 [hahayanyan], 22-05-27 11:35haah for that tube...u need to be quite precise ..haha
u have a router...usually for all DIY speaker maker...
all u need a template and a top bearing bit...
then it can be quite prefect outcome - #6 [Baker.Steven], 22-05-27 11:35最簡單喺撐條一吋木方落個60mm孔度,買隻65mm木鈴梳,Mark中位鑽落去,平靚正
- #7 [hahayanyan], 22-05-27 11:38the potential problem of 木鈴梳......... as 倒相管 need very good matching diameter...if want tight fit..but not using a bit more of filling etc.. glue... haha
最後修改時間: 2022-05-27 11:40:40 - #8 [ckhung], 22-05-27 11:46謝謝#6師兄的提議, 我原先都有考慮過, 是成本最低的但我手勢一般, 之前試過開木板孔, 得電池鑽..有點吃力… TB黎計我見開邊機價位還可以, 唔係成日用應該諗得過
- #9 [hahayanyan], 22-05-27 11:48平價囉機.. 應該內地牌"東成"比較可靠
- #10 [111], 22-05-27 20:34樓主,你先提供一下要鑼的板材有多厚?不要亂用
我唔知你有無用過 router(大鑼機)或 trimmer(修邊機)?
如沒學習用過,頗為危險,由其是router, 手指都可以無埋
就算trimmer, 如落刀太深,肯定會"拍"一聲,嚇親你 - #11 [hahayanyan], 22-05-27 20:53#10
good advice.
lets say..11 mm..... thick
better to do it by 2 passes..for someone have experiences with 1/4 shaft machine
one pass by a dual handle 1/2 shaft machine
if newbie... 3 passes...., u will figure out how to............ - #12 [fireballsiu], 22-05-28 12:51[#10] 111你真是一位好心腸及負責人的人,不忙提醒使用工具時的安全考慮。
- #13 [BenYC], 22-05-28 13:10不如唔好攪啦。60mm上65mm分別可能比相像中少,但工程不少也易出問題。
- #14 [泰tai], 22-05-28 13:37比張相睇吓
- #15 [0925], 22-05-28 13:41
- #16 [hahayanyan], 22-05-28 13:56仲有啲小技巧可以一次過 one pass... By using router..
如果背板背後.. 可以好牢固 install the template, If 面板只係15mm左右thickn SS .. 可以用頂部有 bearing router bit. 大部分ply wood.. Or mdf ok
Any harder wood.. U need to do it 2 to 3 times.. Each time.. 5mm thickness etc..
先搵一塊木板練習兩次 掌握到揸住部router 嘅 感覺.. Then ok..
The issue of having the template at top face.. 因為有可能唔可以 安裝得很緊
1/4 shaft diameter router.. 深圳十幾20 mm厚薄位置條邊減去 2.5 mm 一次過一個圈.. 絕對係可以應付嘅.. 感覺好嘅手感 先練習一兩次
搞得掂嘅
Step drill suggested by 0925 may work.. But really depending on the baffle thickness
Template is important.. If u looking for tight fit.. Not too tight.. Not too loose..
Share the happy outcome.. When u done..
Haha
最後修改時間: 2022-05-28 13:58:55 - #17 [羅密歐], 22-05-28 14:28#15 塔鑽是用於金屬簿板的,應對厚木板並不適合。
- #18 [泰tai], 22-05-28 14:37新手要小心用Router,一彈刀部機甩手就大鑊。
熟手随便用個鐵罐,鐵蓋都可以做template。
最後修改時間: 2022-05-28 14:49:38 - #19 [0925], 22-05-28 15:07#15 + 1
About this item
Material::High Speed Steel(HSS) with Titanium Coated
Self starting:no need for a pilot hole.Cobalt coated to reduce friction and run at cooler temperature.
Spiral Design:3 Flute spiral blade design makes the cutting faster and smoother, and automatically deburred from the hole when the drill bit is drilled
Application:Suitable to cut holes in a variety of material like iron plate, aluminum plate, insulation boards, PVC sheet, etc.
Package includes:1 x 6-65mm HSS Groove Step Drill (13 Steps:6mm, 10mm, 15mm, 20mm, 25mm, 30mm, 35mm, 40mm, 45mm, 50mm, 55mm, 60mm, 65mm) - #20 [0925], 22-05-28 15:43
#15 + 2
最大直徑 65mm 剛好可以前、后對穿,木板厚薄反而冇影響。
下面 video 祇可參考:
最後修改時間: 2022-05-28 15:47:18 - 下一頁 (1 of 2)
- 返回 ...