- #23 [S.Chan], 19-11-19 20:42我部 Micro Seiki RX-1500 用衣車白油咋.
- #22 [twinggy], 19-11-19 12:07So much good info. Tks
- #21 [ilovetheboy13], 19-11-19 11:35好在有淘寶
-
- #20 [babydevil], 19-11-19 08:000:55 recommend 40 weight motor oil....
- #19 [babydevil], 19-11-19 07:48
Vpi Mat Weisfield recommend the use of 40 weight motor oil as a substitute. I have been using it for quiet a while. Messier than clear bearing oil but it works fine. Just a lube. Many audio products are tougher than it looks..... - #18 [achow], 19-11-18 15:36WD40 is not a lubricant. It is harmful to metal.
Your best choice is to purchase the bearing oil from RC shop. It is easy to use.
Bearing Grease is also a good choice to lubricate the bearing BUT you need to put the grease inside the bearing. Therefore, it is not easy to do.
the purpose to lubricate a bearing is to reduce friction. too much will increase the friction and accumulate dust. - #17 [twinggy], 19-11-18 13:15Tks
- #16 [kslsfz], 19-11-18 11:29
- #15 [babydevil], 19-11-17 08:43I just use 40 weight motor oil. One bottle can last for life as you need to only apply 3 drops on spindle.
- #14 [BenYC], 19-11-16 13:36Actually, best way is to get the oil from the manufacturer.
I am sure you can find the needed on ebay or contact the manufacturer direct.
The freight can sound silly to send a small bottle of oil. Yet, damaging the turntable because of using the wrong oil can be devastating. Afterall it is hard to take out once added....(Oil has different type of viscosity and probably some can mix better but some cannot.)
(I lubricated my turntable before. Sounds silly to spend $200 freight for a much cheaper tiny bit of oils in a small bottle. Yet, it I need not worry or keep thinking about it. )
最後修改時間: 2019-11-16 13:41:31 - #13 [twinggy], 19-11-16 12:47Good advice tks
- #12 [ktli], 19-11-15 17:40個人認知,絕大部份唱盤軸承,都是用自潤或自給油的,軸心是鋼材,軸套有用杯士銅,賽鋼,鐵氟龍,或一些特殊材料,軸心和軸套間隙,衹有十來C或更小的公差,在安裝時,廠方應做了適當已注入潤滑處理,除了密封的底部,部份更會裝上羊毛墊防漏油。想維護那轉動部份,有如把機械手表抺油,如果那軸承不是受過甚麼創傷,長時間反過來放置,又或轉動不了,可以不攪便不要攪。
最後修改時間: 2019-11-15 17:53:25 - #11 [cornercube], 19-11-15 15:59
- #10 [rdmhk], 19-11-15 14:38油麻地偉高模型……求地址,吾該。
- #9 [twinggy], 19-11-15 13:23Tks for the further advice
- #8 [kx14cp1], 19-11-15 09:33油麻地偉高模型有,好似50幾蚊
- #7 [12dragon], 19-11-14 21:01網上訂購Bearing油,有好多牌子揀。
未連運費,最平九十蚊,最貴三舊半。 - #6 [twinggy], 19-11-13 22:21Tks for all the above helpful hints.
- #5 [baxiang], 19-11-13 19:43Interesting comment.
That's useful for rusted (ball) bearing that has become blocked. Should a TT spindle become rusted, that TT useful life has probably expired. Otherwise a quick wipe of old lubricants would suffice.
Again, the rule of thumb for lubricating TT, lighter oil for lighter loads, vice versa. Regardless, the heaviest of TT platter is still a light load compared to typical ball bearings, so oil based lube should be most appropriate. - #4 [cornercube], 19-11-13 19:20
- 下一頁 (1 of 2)
- 返回 ...