- #41 [dynaco], 07-06-24 02:20
- #42 [kyushuu], 07-06-24 08:57I matched my Ref3 to Krell FBP 200c class A
- #43 [嚦嚦二世], 07-06-24 09:29Hi kyushuu, is the Ref 3 very quiet? I was interested in the Ref 2 MkII before but gave up eventually because of the background noise.
-
- #44 [forester], 07-07-15 12:51i am using sp-15. There is an abnormally situation which has series of "pop..pop......" noise occasionally especially in humid weather. Anybody can tell me where to fix it?
thx! - #45 [doublesam], 07-07-15 13:52kyushuu兄,唔知你有沒有ref3鮛anuel,如果有又可唔可以借本manuel來copy(純粹幫朋友問)),因為朋友二手買回來無manuel,又想了解清楚D部機,所以特此一問.thanks
- #46 [EPIC], 07-07-15 23:29我的 LS25 MKII 報到!0^.^0
- #47 [dynaco], 07-07-15 23:41我部Sp6B..聽Phono時...本身開機聽好正常...但有時開左半小時..有睇開左2hrs...右薵蝴D就會SI SI ....但AUX係正常....what happened 呢??
- #48 [BarryTseKwong], 07-07-16 08:55請問有沒有人用VT130SE POWER AMP.
- #49 [ivanlau168], 07-07-17 00:05我用VT100MK3, 有沒有人試過用RCA時會有很大的電流聲"d...", 但用XLR時就沒有.
- #50 [mcm], 07-07-17 08:51you forgot to short the pin 2 to earth when 用RCA時.
- #51 [$$$], 07-07-17 12:32高佬張
What is the different between LS7 & LS8 ? Why keep LS7 not LS8 ? Thanks. - #52 [cyc04], 07-07-17 15:28Forester,
I had the same problem before with my Sp11. At first, the noise last for about 5 minutes after turning on the preamp, and gradually it last for half an hour. I replaced two old/bad tubes used for the Phono and the noises disappeared. - #53 [stephli2004], 07-07-17 17:10My SP11 MK2 has similar problem occasionally during start-up, it normally last about 10 mins then disappear, recently changed 2 phono tubes, considering change all tubes if problem worsen.
- #54 [forester], 07-07-17 23:00cyc04,
Appreciated! I'll try. Thanks! - #55 [forester], 07-07-17 23:03stephli2004
Appreciated your response as well. Kindly keep me posted the situation. Thanks! - #56 [dragonball], 07-07-18 00:29ls7 同 ls8我都玩過,唔同聱,LS 8D聱彈跳:,快聱D,volumn 行電子制.我唔鍾意..細聲時會"得得"聲,LS 7 行"鴨屎制"cheap",不過OK喎.D聲柔D..不過分析力..兩部机都好..以上只是小弟個人觀感..如有偏差.請多多指正
- #57 [stephli2004], 07-07-24 07:51forester hing,
Would the 'pop pop' sound disappear if put the pre-amp on mute ?
In my case, mute won't stop the 'pop pop' sound.
Perhaps you also need to isolate the problem whether its by the power or pre amp, try switch-on the power amp only and observe. - #58 [whiteant], 07-07-24 16:53I am using the VT130SE and ls25MK1 with cd2...I would like to upgarde to VT150SE and hope some one can help me, is it very different in term of handling and power between VT130se and vt150se cause the power rated is very closed to each other..
regards - #59 [whiteant], 07-07-24 16:58hi yingying987
I am currently looking for upgarading my cdp and have limited my range to cd3mkII and audionet ART G2. since you are cd3 user could you please how is your opinion of cd3mk2 and as compare to the audionet.
regards - #60 [whlee], 07-07-24 17:28whiteant,
Sorry for jumping in. Regardless of price, CD3 is a rarely nice CD player that impressed me. It's unlikely you will get regret to own it.
Regarding to the driving power between VT150 and VT130, even I have no xperience in these two poweramp, I would grade them very similar. Some spks are sensitive to difference of 20watts while some are not. If you still like your VT130, why give it up? For the price difference between 130 and 150, I would go for a better preamp like SP8 or SP10. Or even change a good set of 6550 tubes for your exisiting 130, ARC factory tubes used to be the best for its products. Many ARC's problem are actually caused by lousy tubes. My classic 150 have been working for me for nearly 20yrs, with factory tubes it works reliably. - 下一頁 (3 of 109)
- 返回 ...
Such as electrocube cap, Mollary cap and so on~
And Where repair is better and how to clean up inside??
THX~~~