Haha

Hehe

Home..... Haha

Haha hahahhaahhahaahha

It need some rescue haha




最後修改時間: 2020-10-19 17:47:43

Yes. Did not know those red screws for ...until trouble shooting for rumble.and noise..for a few hours..I then read the manual carefully...haha , never really to some golden advice.. READ Manual first hahahaahahahaaha


And have order one set of ceramic bearing and 2 little plate...for rmb 75, why not for rmb 75, then I do proper cleaning

As the original ball bearing ..the surface se to had worn


Things to learn..and am getting a L78 SE today too


Thx so much for pointing me to a right path

Haha

最後修改時間: 2020-10-19 14:04:16

oh, when dismantling the spindle bearing assembly, be extra careful when you use a nose plier to take out the circular clip, it could fly off and you'll never find it! i'm talking from experience, ？

'haha', from the photo, i think you still have the transport screw fastened! unscrew it and let the motor mount spring do its job. Pull off the bottom plastic cap and give the whole spindle bearing and the inside a good clean. if you don't get a new thrust plate then just reverse/turn it over as there has to be a little dimple developed from all these years of pressure acting on it.

i cannot rate the lenco stock arm so no comments :-)

There is more to it than meets the eye.

It is like a raw diamond that it needs clever cutting to bring out the best and create the prefect gem.

Have more fun with more tweaks.

最後修改時間: 2020-10-18 04:24:03

Haha...that thing is clever, simple but so clever haha the speed and the cone and the idler ,the way it get the speed...and the adjustment haha
I start to understand that table haha

Not close to good,as far as the w&f % is quite high， but good progress for the day 1

Tomorrow..find something to use as the antishaking bar ..and find some rubber feets

Fun






最後修改時間: 2020-10-18 02:30:44

Haha trying haha

Been lazy after that can of not too cool coke zero

And this is what I am upto now

Not dirty but seem need to take the shaft block off...and then take.the shaft out for lub...

Haha tomorrow

Shall ask for help..if I mess things up

Thx for the head up

I am delighted haha as it turns



Haha

I bought one many years before, remember that was cleaning and lubrication of the motor. Not electronic device coz all mechanical parts only.

Expect it is sort CAP issue or even it is purely mechanical too , but no harm to replace to new motor cap..etc..

and the Anti-shaking " bar is missing too

Hopefully it may just be a simple exchange of some caps, nothing too much a challenge to you anyway.

Haaha..can power on

And at 45rpm..only 40rpm..and at 78 rpm... Can only reach up to 40..then drop....

Se easy fix..

Shall open it after some cool coke zero

Haha





最後修改時間: 2020-10-17 21:36:59

Good job and welcome to Lencoheaven.

Looks decent and quite complete though may need a little bit of TLC.

Hahaha... Day 1 of a lenco L75 owner

Haha..

Which is not quite working... Haha

Just home with it

Haha

thx thx thx thx thx

even it is or not... ,it is nice to be educated

thxxxxxxx

the seller for the lenco is busy..and i am busy with a vintage Akai M8 tube reel to reel too haha

no biz association with them but wanna share this brand as well, similarly priced as the PTP offering:

http://sound-carrier.com/utps-40w/

thx thx thx...for sharing

euro 1100..............WOW