- #24 [hahayanyan], 22-11-27 19:06
- #23 [appleseed], 22-11-27 18:47因為此喇叭已停產多年代理都要問有無高音同絨布所以要等覆
- #22 [appleseed], 22-11-27 18:38收到唔該曬師兄!
-
- #21 [blackspin], 22-11-27 17:33Before placing the diffusion sticker....... but now the factory changed the "Sticker" to Alpaca Mat, much thicker and expensive.......
最後修改時間: 2022-11-27 17:35:22 - #20 [blackspin], 22-11-27 17:31I think the front panel diffusion sticker is just like my speaker, but the Verity Audio one is more rigid and hard to remove.......... mine is more easily to replace
My driver unit screw can be seen after remove the diffusion sticker, I think the Verity Audio should be the same - #19 [hahayanyan], 22-11-27 17:25可以從背後脫出高音, and get it out from the woofer hole, 以及不需要移除這塊布
機會很低很低
Dealer 的維修手工 for glue 塊面
不見得會畀任何人出色
If the maker happy to sell u A few pcs of that..first may mostly ugly, however 2nd or 3rd attempt may ending up nice..
So it is quite essential to get a few pcs from maker or cut ourself
Cannot see 我們任何一個人會做得比較差, or 比較好, is about luck and the learning from the first attempt
Good luck
Such a nice speaker.. And good looking speaker..
最後修改時間: 2022-11-27 17:25:40 - #18 [appleseed], 22-11-27 17:18攪唔店甩唔到都係要等代理覆。
- #17 [CS168], 22-11-26 22:59
背後低音槽 " 反射孔 "
都可以照到高音,結構,
部份低音膠槽管道,係可以小心取出。 - #16 [appleseed], 22-11-26 22:09我睇下得唔得先唔該師兄
- #15 [bao19922002], 22-11-26 21:49如果拆開咗低音,可以用塊鏡申入箱裡面,睇下高音後邊是怎樣安裝的,唔知會唔會係扣,一扭就開。
最後修改時間: 2022-11-26 21:50:31 - #14 [appleseed], 22-11-26 19:55唔該曬師兄!已問代理等緊覆
- #13 [BenYC], 22-11-26 17:41I would suggest you ask sole agent how much it cost to repair first. Handicraft has a learning curve and most importantly, factory may send the driver and spare mat for replacement.
- #12 [hahayanyan], 22-11-26 17:20step 1) apply heat..and gently peel that off..partially or completely
step 2 ) measure the thickness for that material
step 3) remove glue
it may take u 3 mins or less to peel that off...........and 10 mins to remove those old glue...
step 4) ....good luck for putting it back
....
why step 2.......
as it may fail and super ugly
as we know the thickness now..
go to taobao ...buy similar material , laser cut them also taobao........according to your drawing...with some luck,...those material may have self adhesive too
suppose it shall change the high frequency responds if the material are very different
oversize the edges... trim it
or...excat...................
u may also ale to get those "cut " of that from the Marker too......... , they may send u free toooooo
最後修改時間: 2022-11-26 17:31:02 - #11 [V.C], 22-11-26 17:12呢啲手藝嘢睇似簡單做落要好精細,又無原廠布,不如考慮返原廠整啦!
最後修改時間: 2022-11-26 17:14:51 - #10 [appleseed], 22-11-26 13:41re
- #9 [CS168], 22-11-26 11:57
有茅背面+-接線插座相片看? - #8 [appleseed], 22-11-26 11:20唔該曬師兄!不過塊絨布貼得好實好難攪
- #7 [Ck2007], 22-11-26 09:32我都係識皮毛、喇叭單元甩線度唔通即燒咗要換
- #6 [appleseed], 22-11-26 09:12師兄應該點樣度?我試度過高音正負不通,中音就通
- #5 [Ck2007], 22-11-26 08:22見你都拆咗低音螺絲、先檢查分音器、度下高音有冇short咗
- 下一頁 (2 of 3)
- 返回 ...
Any idea why the tweeter goes bad?
I love some of them, as it has nice tone and very 3D