- #101 [41450686], 17-11-23 10:00Try to change the DSD over PCM setting first. From yes to no or from no to yes
- #102 [sugnama], 17-11-26 11:46strida 兄, Volumio 還是MOODEAUDIO 好, 打算入手Raspberry, 新手一名.
- #103 [fr3d3r1ck], 17-11-26 12:25Volumio比較易用,Moode轉了open source安裝需要點時間,先試volumio
-
- #104 [sugnama], 17-11-27 14:49好的, 謝謝回覆!
- #105 [strida], 17-11-27 14:52moode 最好聲,支援最多i2s 擴充板,不過設定比其他兩個難D
- #106 [strida], 17-11-27 14:53moode 3.8.4
- #107 [strida], 17-11-27 14:56is2 support
- #108 [Calls], 17-11-27 16:06唉,小弟跟啲師兄改咗,但都係一樣沙沙聲,希望同好會啲師兄幫幫手,Thanks
- #109 [strida], 17-11-27 16:43點改?播時沙沙聲,用乜os
- #110 [tmcc2006], 17-11-27 21:07#108
你要講清楚整個流程,用嘜線,嘜板,點轉i2s,用嘜線輸入LKS....
影相睇下有無駁錯 - #111 [wong40], 17-11-28 12:23Calls 兄,
去年試過LKS的i2s,出聲正常(不代表好聲)。由於當時有幾款板,忘記是否有試 Raspberry.
1. ssh 入 Raspberry
2。nano /etc/mpd.conf
upsampling 可在 audio_output 內『或』外 define. 只可define一次
在audio_out 內
audio_output {
type "alsa"
name "LKS"
device "hw:Amanero,0"
format "192000:24:2" <------
}
在audio_output 外。
audio_output_format "192000:24:2" <-------
不知以下是否需要(朋友說用了好聲些,但raspberry 會吃力)
samplerate_converter "soxr very high"
注意: LKS 一定要192000 才可以正常出聲. 24 可用*代替。 "192000:*:2" - #112 [Calls], 17-11-28 13:28Wong40兄,小弟今晚照你方法試試,萬二分感激
- #113 [ll200511], 17-11-30 20:49Hi Ching,
I have the same problem, pi3 i2s hdmi board to LKS dac, sa sa sound.
How to edit audio_output ?
I am using Volumio. Generic DAC
sorry I do not know how to type Chinese
thanks - #114 [Avfire], 17-11-30 22:40You may select the sampling rate in this UI. What is the sampling rate shown in your lks?
- #115 [Avfire], 17-11-30 22:43Pic
- #116 [ll200511], 17-12-01 00:24thank you Ching.
change to 192k , it works. GREAT.
but it cannot play DSD file!! - #117 [hema], 17-12-01 11:43DSD over PCM (dop)———-yes
This is my setting - #118 [ll200511], 17-12-02 00:36it can play DSD now, thank you Ching
but it change to PCM 192k and sound not so good as DSD - #119 [Calls], 17-12-03 14:48唔知有冇set錯,都係沙沙聲,求各路英雄幫手
- #120 [Calls], 17-12-03 14:50求各路英雄幫手
- 下一頁 (6 of 39)
- 返回 ...