我都有個Thorens126 Mk II + SMEIV臂。呢個盆係我後生時買既，記憶中係千幾錢，幾十年落黎重好正，不過現時退下第一線。

hetzer兄:
我改了臂內至唱頭那一段接線.在鴨記找到最幼細鍍銀的但夾仔沒辦法找到相同的.唯有自己又想辦法用簿銅改成.唉!!好彩在鴨記找到簿銅.

夾仔都屈到，手工唔錯wo，我都有部Dual死左唱臂線封緊塵，太老爺又唔值得花錢整，遲下學你整返玩下。
新夾仔可以去永盛買Audio Technica的Head Shell線，一套4條8個夾仔約$100。軟銅好易氧化，你個夾都係玩住試下聲先，長遠唔係辨法。

I use TD160 super + SME3009 improved + Shure VST
其實3條彈弓會唔會虧???
因為可難調校個link至水平....
有無方法, 請各位師父指點~~~
THX~~

Thorens!!經典中的經典!!!
希望有更多Fans出黎支持!!

睇黎TD160 super都幾多人用.

我用TD160 super + SME IIIs + Shure M55E/Pioneer唱頭

簡單好聽.

hetzer兄:
你簡值係我恩人!原來可以用Audio Technica的Head Shell線代替.仲有夾仔正呀!!

Dear Hetzer,

My TD-126 MKIII is using SAEC WE-308 arm. Just a very good work horse!

Actually, the materials used in 70 - 80 high end audio are very good. So they just need normal maintainese to keep their conditions.

LFYeung

LFYeung

我用緊Thorens TD126 Mark III + Audio Technica AT1010唱臂 + Monster Cable「音魂」mc唱頭。全部都係老友借比我玩的，好聽到唔想還番比吽I

edwardfkw兄
條彈弓一般唔會有問題，除非生蚳嚍_，又或者亂教攪變到左形，否則可以用幾十年。除160 Super外，其他160彈弓有海棉，海棉一般都係十年貨仔，霉左其實可以索性唔用。反而彈弓膠墊比較易變形，但其實Thorens D料算十分好，我D膠墊二十幾年仲用得。
教彈弓唔算好難(比起LP12已經算易)，但要些耐性，因為教完唱一排setting會走位，如是者要教三幾次個setting至stable。以下是小弟一些心得。

第一次教：先反轉個盆(當然要除左個platter和lock實之臂，誚n個dust cover)，打開個底板。將三條彈弓拆左出來，清下蚸M加少少防蛌o，清理膠墊等等，將個subchasis對正位(三口鏍絲在三個孔正中間)，將彈弓裝回，但只收一半。
反轉個盆，將盆放在兩張椅中間(我用Ikea的木轉椅)，較兩邊高低及攝紙至盆座大約水平(木邊作準)。
裝返條belt(千萬要有belt及唱臂線至教)，放返個platter同matt，再加一隻一般重量的LP。
跟住用手指扭三口絲母，
1) 先教轉盆至大約水平(用細平水尺在全matt上check)
2) 再教轉盆底離地5-6 mm。
教絲母要重複多次，每次讓轉盆轉一陣。留意轉盆底離地有無時大時細(一般一個圈唔應該超過半mm)，如果朗來朗去，就要check下條belt同埋主platter和副platter的接合面是否清潔。
最難係下一步。
打橫將個轉盆向四個方向推，留意是否可以自由移動(好似隻艇浮在水上咁樣)，一般都係fail，會卡住。此時就要轉條彈弓(係彈弓，絲母唔好移動)。條彈弓其實轉唔係完全對稱，當轉條彈弓個盆就會水平方向移位。較到個盆可以水平自由移動，唔會卡住為主。但較完之後個轉盆又唔再水平，即係話又要較絲母，如是者來回幾次就較完。

玩幾日後再check水平和clearance，再返tune。返tune唔洗拆底板，用枝bob頭在個底板那三個孔教就得。

Dear LFYeung Hing,
SAEC 308...
Oh I almost bought it. Finally I choose SME 3009 SIII (because of the price and the brand preference).
This is one of the most stupid choice in my life. I still feel deeply regret as I didn't buy SAEC.

Hi any brother know what will be the fair market price for a Thorens 150 MK1, fair condition, no Cartridge but with original tonearm. thanks!

any brother can advise?

I like to know where to buy the belt ?

新旗艦!!

New Entry Level Turntable

xxx111 hing, Thorens belt is still available from the agent but very expensive.

xxx111 hing,
I order my here. About HKD$280 including H&D. They sell crone belt. So far so good.
http://www.elexatelier.com/thorens.htm

You can also find NOS true Thorens belt from some other suppliers.
http://www.theanalogdept.com/replacing_the_belt.htm

bbq_123456 hing,

There is nothing called a market price for antique Thorens TT as the supply is very small and demand is also very small. Also the condition of antique TT can vary very much. TD150 is a classical TT. Almost all three points floating TT (LP12, TD160, Systemdek...) are copying it. It uses very good parts. Up to my memory, TD150 was made in Swiss by original Thorens while TD160 was made in Germany after Thorens was sold (so TD160 is "mass production" clone of TD150). However it had stopped production in 1972 so the age is 36+.
May be you can use the price of TD160 as a reference line. You can search in Review33. If a TD150 has equal condition as a TD160, it should worth more than a TD160.

hetzer & tkchan hing :

thank for the infromation.

Besides , any one try those from Ap liu st. of SSP.