- #61 [cobra], 21-12-14 18:18跟住隔一會再睇,個盤停左再冇反應........
- #62 [cobra], 21-12-14 18:20我處理得好差,開左一個鐘去到73度,係人係鬼都要熄機睇吓乜野料先啦.................
- #63 [hahayanyan], 21-12-14 18:21Hhaha 73 degree C... Still ok
一個夢碎了 ok
Take some rest... 開始另一個dream
check the installation of the retracting spring..etc
有得搞嘅爭少少..
Haha
最後修改時間: 2021-12-14 18:25:27 -
- #64 [Dynaco], 21-12-14 18:23個軸加左油末?
電容數值ok??? - #65 [hahayanyan], 21-12-14 18:26拆開洗咗未? Those 2 link...
最後修改時間: 2021-12-14 18:27:09 - #66 [8po], 21-12-14 18:44The behavior of your 401 is like fitted 60hz pulley
- #67 [hahayanyan], 21-12-14 18:45if it is 60 hz and at 50 hz hk...he should not get more than 30 rpm worrr
- #68 [8po], 21-12-14 18:49Haha: maybe Cobra hing is running at max speed?
- #69 [hahayanyan], 21-12-14 18:54if before he clean the machine the rpm..was 27 ...25 rpm.. i would guess.it is a 60 hz machine.. etc..
but it was starting at 32 rpm........sign of poor condition table..
even if it is max speed...lets say +/- 6 % etc... ,it would be under 30 rpm..
haha
i had worst Vintage tables at super poor speed...it will be fine.............. after services... his case ..may not even need new parts... good luckkkkkkkkkkkkk
he can still have his garrard dreams
Any 301 401 user... Here... Hows the motor operating temperature?
唔通佢真係要拆開個摩打洗乾淨佢
希望佢會成功
亦希望佢冇犯咗一啲好低級嘅錯誤.. For example... Oil at the idler and the rim contact surface.. Etc..
Haha
最後修改時間: 2021-12-14 19:06:38 - #70 [cobra], 21-12-14 19:1233rpm pulley size
- #71 [cobra], 21-12-14 19:1445rpm
- #72 [hahayanyan], 21-12-14 19:18hi cobra
are u sure it is a 50 hz machine ?
if it is a 60 hz machine..and if this 401 have +/- 12 % range ( i am not garrard user.. haha...i have no idea) then it is exactly what happening to u now.........
u may need to clean the VR of the speed control knob..too ... "contact cleaner"
have u done "C"
haha
最後修改時間: 2021-12-14 19:24:28 - #73 [cobra], 21-12-14 19:25我好單純,一直都冇懷疑佢,HaHa
- #74 [hahayanyan], 21-12-14 19:31haha...ok good it is 50 hz
and clean those VR too
haha - #75 [Dynaco], 21-12-14 19:38If 100V, must notice about motor electrical jumper connection
- #76 [cobra], 21-12-14 19:49有,將Jumper跳左220V
- #77 [hahayanyan], 21-12-14 20:08so nice.....having jumper for 220v...
so nice.........
add oillllllllllllllllllllllllllllllllll
加油加油一定得嘅
BTW.. Any one compare 124 to 301/401
And how's 301 vs 401?
haha
最後修改時間: 2021-12-14 20:09:50 - #78 [Dynaco], 21-12-14 20:28301 有分oil and grease 版.
- #79 [hahayanyan], 21-12-14 20:45Seem there are more topic or chat for grease version...
- #80 [rcywong], 21-12-14 21:04You need to have another motor pulley fitted, if the turntable is 100 volt version, 60Hz. Alternative pulley is required for 220V, 50Hz.
You better check the pulley is correct or not?
最後修改時間: 2021-12-14 21:09:27 - 下一頁 (4 of 11)
- 返回 ...