- #41 [cobra], 21-12-02 21:28
- #42 [hahayanyan], 21-12-02 21:44haha ADD oiL
12 SEC IS QUITE BAD............. but it will be fine
this may help
https://pinkfishmedia.net/forum/threads/garrard-401-spindle-and-motor-service-instructions.187098/ - #43 [hahayanyan], 21-12-08 13:36haha any update ?
-
- #44 [cobra], 21-12-09 16:24HaHa,昨天13:30我剛做緊手術HaHa
暫時要停幾日才搞,首先處理粒機米,支1.8mm螺絲批淘緊落來,
希望開到粒機米,另外想問no 2 grease問題,前排去中石化油站,
佢哋話冇得賣黃油,是否要去大間D中石化油站才有。 - #45 [hahayanyan], 21-12-09 17:41通常係去嗰啲 機油嘅分銷商可以買到
嫌麻煩唔想搵就喺淘寶訂返上嚟
做完手術都應該多多休息 haha play play table.. 都應該係一個 幾好嘅休息活動
斷估你都明白摩打係邊個位置入油 haha
無聊想搵啲嘢玩, 係可以加一個電源供應器令轉速等等有更好嘅優化, from the lenco group people using a ac power supply.. Which alter the ac voltage and frewucy etc.
To get the right excat speed etc.., that powrr supply also ok for 401 type of motor.. I guess
Haha
最後修改時間: 2021-12-09 17:44:31 - #46 [cobra], 21-12-14 09:03終於除埋佢件衫一窺全豹,甩埋粒機米啦。
最後修改時間: 2021-12-14 09:12:02 - #47 [cobra], 21-12-14 09:08Motor add oil 係未直接落B位3個孔位置,需要打開嗎?
A点枝軸承是否直接滴油落去就可以?
唔該大家(*_*)
最後修改時間: 2021-12-14 09:09:50 - #48 [hahayanyan], 21-12-14 10:40雖然我沒有401, but oil to B see. Right
Haha - #49 [cobra], 21-12-14 11:49加晒油,都係32.6轉................太令人心碎了
玩玩吓盞燈仔都自己熄,一著機一閃即逝,乜事呀
跟住向第二個方向諗
電容問題(盞燈一閃即逝,會否跟電容有冇關係?
eddy current disc(係未指磁石個組嘢) - #50 [8po], 21-12-14 11:55#47
A is more direct
B are just rivets for holding the bushing cover. - #51 [cobra], 21-12-14 12:06#50
Motor 加油怎樣處理,ThX - #52 [hahayanyan], 21-12-14 12:08according to thios photo..it is really an oil inlet hole..around here
and there is always motor have such oil inlet hole too - #53 [cobra], 21-12-14 12:21重有樣嘢請敎,個motor都好鬼熱,有燙手感覺,正常嗎?
- #54 [hahayanyan], 21-12-14 12:28i am not a garrard user, in general i would say..is ok for a motor less than 70 degree C (most magnet operate normal within 70 degree C)
if it reach 90 degree.......it may have issue, as some magnet lose power at such temperature
hot under loading or without loading ?
u have a infra red thermometer around ?
how clean is your idler ? need to be super clean...etc..
if u think u have done enough service...if u still having thsoe final kick of the speed... i would say...it is likely related to your idler condition ...
haha
最後修改時間: 2021-12-14 12:37:46 - #55 [8po], 21-12-14 15:01#51 add to A directly, just few drops
#52 the oil go thru the hole on eddy disc will end up to the sunken part of motor housing then the shaft. I will take our the eddy disc to oil it to save from mess.
#53 it runs quite warm, 5-60°up. If it is too hot, either the bushing is dried or too heavy load. Did you disassemble the motor before? - #56 [cobra], 21-12-14 16:13#55
未拆過,但係好有興趣想試,HaHa - #57 [hahayanyan], 21-12-14 16:18How's 45 speed setting
If it is only warm not hot..
Run it a few hours.. Haha - #58 [8po], 21-12-14 16:41#56 can you measure the dia. of the motor pulley? @78rpm
- #59 [8po], 21-12-14 17:01@33.33 rpm, largest dia. Part
- #60 [cobra], 21-12-14 18:16OMG,我的Garrard夢破碎了....
- 下一頁 (3 of 11)
- 返回 ...
如果個轆拖住的話,我諗捱唔到5秒....hahaaa