- #1 [cobra], 21-11-25 10:06
- #2 [cobra], 21-11-25 10:17正常惰輪直徑有幾大?
- #3 [MOSbill], 21-11-25 11:12My Elac old turntable had the same problem too..... cannot find a solution.
最後修改時間: 2021-11-25 11:13:13 -
- #4 [hahayanyan], 21-11-25 11:16我之前的三四部 lenco... Elac.. 好舊好殘舊買返嚟轉速都super slow.. 唔記得邊一部啦30都唔夠
乜嘢都唔使換.. Clean the shaft..of the main bearing.. Cleaning bearing housing.. Etc.. Add new oil...
Clean the idler shaft.. Etc..
Clean the idler contact surface..
Clean the platter contact surface...
Very very clean..
Also some sort of tension device.. For engaging the idler.. Those need to be very clean.. Etc..
Motor... Clean it.. Add some. Oil etc..
Now +/-0.07...0.05% et
For 401..more to clean..
Without cleaning them.. Is so hard to find out what goes wrong... If something goes wrong
Haha
最後修改時間: 2021-11-25 11:21:40 - #5 [cobra], 21-11-25 11:34收到曬師兄,Thx
- #6 [hahayanyan], 21-11-25 11:38one of the Elac...automatic...
lovely to look at their auto function... is quite a good table.. after a few hours of effort....everything work so smooth...haha so happy
haha - #7 [hahayanyan], 21-11-25 12:11記得睇清楚401, 係用乜嘢潤滑... For the main platter bearing
Have fun - #8 [bambino], 21-11-25 12:17全新301 idler wheel, 可同401共用的. 66.70mm diameter. 同你的數字少過1%分別. 應該吾係轉速問題嘅原因.....
最後修改時間: 2021-11-25 12:21:33 - #9 [hahayanyan], 21-11-25 19:55haha wait for your good news
may be the speed ......will just be ok..only cleaning the idler edge ,and the coupling platter surface..
haha - #10 [8po], 21-11-25 22:58#1 之前work?
- #11 [dynaco], 21-11-25 23:281/電容有無問題?
2/ motor有無加油???
3/ 軸有無加油?
4/ eddy current disc 正常??? - #12 [cobra], 21-11-25 23:33二手入放左一段日子,試識行識走就放低錢抬番屋企.
- #13 [cobra], 21-11-25 23:39HaHa,我試完再通知大家,唔該曬.
我一樣都冇添添油,真係抵打patpat. - #14 [hahayanyan], 21-11-26 12:00嘗試完記得同大家分享
因為你呢個問題有好多人 都會碰上
對其他人很有參考價值
Haha - #15 [cobra], 21-11-30 19:27清潔,加油後有進步,遲D換隻稀少少嘅油俾主軸承試試,
希望有好消息. - #16 [cobra], 21-11-30 19:33有粒機米拆唔到,焗住成個拆落來慢慢搞,
最後都搞唔掂粒機米,唯有係旁邊渗落去。 - #17 [hahayanyan], 21-11-30 19:34nice................
haha what oil u are using nowwwwwww ?
give some heat...etc..and try again.......top remove that screw...
haha
最後修改時間: 2021-11-30 19:35:40 - #18 [cobra], 21-11-30 19:36得閒都會打散再重裝一次,順便清潔吓。
- #19 [cobra], 21-11-30 19:40N年前應該係D唧筒用嘅油,有冇好提議。
- #20 [cobra], 21-11-30 19:41x
- 下一頁 (1 of 11)
- 返回 ...
最後修改時間: 2021-11-25 10:07:12