- #213 [hahayanyan], 22-05-06 17:26
- #212 [dynaco], 22-05-06 15:50hahayanyan hing,
is it easy to remove the idler wheel??? Just want to try to clean it
Thx - #211 [hahayanyan], 22-05-06 15:20your problem is more about at around the idler ............
haha..then u be ok soon..after u do some service at the idler area.. -
- #210 [dynaco], 22-05-06 15:03hahayanyan師兄,
我净係攪過支軸,轉過用好薄既油,换過thrust bearing......
等我放假時再攪吓先
Thx - #209 [hahayanyan], 22-05-06 14:51分享下你多一些的drifting 狀況
你搞過啲乜嘢改善, and 有啲乜嘢 可能應該要攪蛋 未搞呢
Let's see.. If we can troubleshoot together.. And some other c hing may have some skill to share too
Drifting... 例如曾經轉33.7號平均冇問題 for a few minutes .... 突然間唔知點解去到34點5.... 平均,
但係又不然間轉去三十二點三又一段時間...?
Drifting around 33.3 +/- 2% level?
Remember.. Quality Table at that period.. 0.1..0.2 % should be very easy to archieve.. Etc.. .
U Shall be fine after more effort..
No harm to double check your line voltage stability too
最後修改時間: 2022-05-06 14:58:30 - #208 [dynaco], 22-05-06 09:46就係301盤,speed drifting .........攪到人都癫
- #207 [hahayanyan], 22-05-05 17:32有快有慢 範圍 去到什麼程度?
如果你講緊冇需要speed control 嘅唱盤
佢嘅快慢範圍其實都好窄.. Some very very old table.. May be +/- 2%
Thzoe Garrard 401...lenco.. Etc.. 大部分都喺+/- 0.X% 一個小數位後的% 甚至更低 from 33.3 reference speed
As 50 hz is fairly stable...
如果你碰上一個 用這些AC 同步馬達... Always plus or minus around 37rpm, or 31rpm...
呢一個應該係其他物理上嘅 問題.. Not the motor issue.. Etc..
For example.. Garrard type.. Or other belt driven... 可能係皮帶或idler lose grip
If it is lenco.. Idler and 雪糕筒的接觸點錯誤 etc..
其實嗰啲motor 去到401 嗰個年代已經可以做到 0.1% accuracy...
Etc..
Haha
最後修改時間: 2022-05-05 17:32:52 - #206 [dynaco], 22-05-05 16:50hahayanyan師兄,
有無試過個盤,無俾speed control都會時快時慢??
Thx - #205 [hahayanyan], 22-03-31 16:07Rule no. 2
Stronger always better too
Rest offer strength too
Good luck
Life is full of fun.. If we create some
We all have mistake and moment of weakness.. Lets goes and forgive ourself.. And get some rest.. And start again..
Take care
Wait for your good 401 and 75 video
Haha - #204 [cobra], 22-03-31 15:54多謝Haha
讓一切回到正常,去勇於接受生命/生活的轉變/改動。 - #203 [hahayanyan], 22-03-31 12:44Hey..cobra
有一件事情一定是對的..
Simple. Rule.. Make today not bad
. Or ok.. Tomorrow more chances to be better.. As long as we may understand or have a habit what is the right things to do today...
明天 一定可以會更好
Add oil
Good luck and take care
Toy later..or now if some toy may make tomorrow better.. Then toy now.. Or later..
Haha
最後修改時間: 2022-03-31 12:45:44 - #202 [cobra], 22-03-31 12:39闊別接近2個月,再次按入來看看 ..............
看到HaHa兄的呼喚.............真的百感交集。
新年過後,心情一直低落,3月頭再出現一些問題,捱到上週終於爆煲,事後檢討這兩個月,不斷關注自己無法改變的東西,投入到自己控制不了 .........
希望事情告一段落,聽太太的勸告,未來的事將來去面對,再想都浪費時間,
我希望做到~活在當下。
最後修改時間: 2022-03-31 12:39:55 - #201 [dynaco], 22-03-26 11:51昨晚試左3種油, free rotating 都係十秒左右, 但wow有改善的
用33rpm試
1/ 衣車油 0.31
2/ 衣車油+ graese 0.36
3/ 3號油 0.21 (oil最thin)
最後都係用3號油
仲有個grease盤未試....
ThX, haha師兄 - #200 [hahayanyan], 22-03-22 13:19haha i do not know...hows the CTC build, and they may have more than 1 bearing for 401/301 too...
they shoud tell u at their oil bottle ?(come with the CTC.. sometime they tell how many drop..or how many CC , and u may not have it..as u said..it come with the table
cannot find those "bottle" photo from CTC yet
does it have a Felt washer?
open that bearing.... never assume there is nothing missing........... usually from the bottom haha
if u do not find how much oil...for that CTC... send them a message at the facebook page..
or keep drop by drop adding until u see oil start coming out from the top gap
最後修改時間: 2022-03-22 13:26:05 - #199 [Dynaco], 22-03-22 13:02hi 師兄,
我買返來已經係CTC bearing 了,油有無話入幾多??
Thx - #198 [hahayanyan], 22-03-22 12:13this is how the the bearing look like
lets say...if there is no external object / big dust..etc..inside the cavity ..
u may feel a little bit of friction in between " felt ring washer" and the shaft
if u feel quite a bit of friction...check..if that "Felt" are dry and hard ? it suppose to be soft and filled with some oil
also check the condition of the bottom brozne thrust pad.. to see if it is in very poor surface condition and clean it..etc..
enough oil ? nothing damaged or deformed...every things straight..etc?
if nothing deform and felt is soft and oiled...and enough oil ..etc... if u still feel uncomfortable about the "high住咁"... u may need to upgrade to some 3rd party bearing etc..
最後修改時間: 2022-03-22 12:21:34 - #197 [Dynaco], 22-03-22 11:24hahayanyan 師兄,
如果platter未放落盤度,但支軸好似有野high住咁...
係咪咁架。。 Thanks
重申,我入左aeroshell no.3 oil - #196 [hahayanyan], 22-03-17 11:08Quite a long...... Spin down..
- #195 [hahayanyan], 22-03-12 17:17Cobra....
U ok.??? ... Where are u.....????
We miss your 401...
Haha
最後修改時間: 2022-03-12 17:17:37 - #194 [rcywong], 22-03-12 16:57Or,...
- 下一頁 (1 of 11)
- 返回 ...
in some cases..the idler arm spring may need replace..
clean it.....apply some oillllllllllll....to the idler bearing..
clean all the contact surfaces..etc..
mechanical link...cleaning..and may need some grease..etc..
u be ok
haha
最後修改時間: 2022-05-06 17:30:39