@projectx Ching...

其實加入外置分音主要用於將低頻80Hz或更低分比對Sub，希望能減少主Amp嘅負荷又可以令塊板專注中高頻令人聲更特出，而低頻部分主要留比對Sub去搞掂。因顧及到靜電啦叭對高中低頻相位嘅先天性問題，部電子分音亦擔當咗delay工作, 將高中頻調慢去配合對Sub，從而希望唔會產生先後快慢問題。經好多次擺位調節，目前出離效果令人滿意。

Interest pls call 95153188, joe thx

有地方玩這對CLS真係樂趣無窮, 聽弦樂及結他一絕, 但加電子分音對音色會否有影響呢?

目前自家用緊對大門板,CLSiiA 做兩聲道，主要聽人聲與簡單樂器為主，唔著重低頻，但都裝左外置電子分音每邊獨立接左只英國rel作sub bass 補償。前後機種全麥佬。

用過多種speakers, 包括Apogee, maggi 3.6, Quad esl63, 傳純音箱, horn 等, 論音色, 靜電是不二之選, 論氣勢, 首選horn, Apogee太利, Maggi 低音似打棉胎, 中音太膠, 高音OK. 所以現在只玩靜電及horn! 師兄呢?

心有同感，搵部好amp去推真系唔易，因為正如師兄都講ohm值系唔同頻率時變化太大，amp性能唔好就會燒機。

其實小弟都挑戰左自己好多年啦，我一直玩開靜電，前後中左右都系非靜電莫屬。好同意你對靜電嘅觀點。

有用柯頌V8i(250w), Ben David model 28(180w), 及Allegro 300B, 頭兩部都很滿意, 300B就力有不逮, 全部都係平野, 但牲價比很高.

师兄用紧乜amp去推,分享下好...

現在玩Aerius I, 要想中高出得靚一定要離牆, 對後級的要求亦高,要出動巨無霸才有聽頭, 出面二手價不貴, 有機會買對回家挑戰吓自己.

projectx兄, 呢条帖都有成年几,唔知d师兄仲有無玩紧静电呢.呢次偶然钟咗入离,见無乜师兄再跟进,咪试下睇将帖搞番起个话题.师兄玩紧乜型号呢.

ML唔易玩架, 無論擺位, 對器材質素, 都要求甚高, 一旦玩得好, 再聽其他 speakers 時就會覺差點韻味(除了quad).

呢條貼唔知仲有無師兄想繼續落去呢?

projectx hing, I had been show once, but failed. I tried show with cleansing liquid again, still wait it dry and test. Hope it can work.

我對Aerius到我手不過是一两個月的事.我先前係用Thiel 3.6,两者相比較:3.6分析力高一點,偏硬.ML則口型較大,深闊都不及3.6,但柔一點,聽來舒服一點,我也有部胆机(彷9)日後駁咗再講. thx

好耐無同大家講ML了、我的Aerius I 經洗白白及break in 後巳回復惜日光芒。以前用大力膽機推、現在用9V的300B也推得很靚聲。還有：ML對speaker cable很敏感、貴價野未必夾、反而用對幾舊水的Klangfilm就超好聲。
nmg兄你對Aerius現況如何？

＞disconnect包唔包括喇叭線?

Just the power will do. It is just to make sure the static panels will be fully discharged. Although all later ML models have auto power on (i.e. panels not charged when no signal), I would just unplug them to be safe.

olddude hing:
disconnect包唔包括喇叭線?
THX!

this band makes no box sound speaker ,super transparent and clear .will be my next upgrade target for sure .especially the new model was more easier to push and the bass was much better than before .it worth to owned it nomatter what

＞我當時想用風乾洗,想是不行的

You can try to vacuum the panels instead. Vacuuming is recommended by ML. It doesn't do as good a job as washing but less troublesome and should suffice in most cases.


BTW, before you vacuum the panels, you should disconnect it for 24 hours first.

最後修改時間: 2011-10-04 12:36:03