- #27 [accudude], 20-07-07 11:06
- #26 [tigerlck], 15-10-17 05:15thx
- #25 [Butter], 14-03-06 13:16有指示牌呀。照做可以？
-
- #24 [254mm], 14-03-05 18:39應該可以跟 label instructions 照做, 不難, 除非冇 label, 咁就煩好多, 要慢慢跟, 搭錯燒牛就大鑊啦
- #23 [butter], 14-03-05 18:30應該可以跟顏色更改。
- #22 [GW], 14-03-05 12:40機内接線頗雜，需要師兄指導好喎！
最後修改時間: 2014-03-05 12:43:05 - #21 [butter], 14-03-05 00:56I can't find 230Volt in DP90 & DC91. I FI find both 220 & 240 volt.
I want to change its voltages from 100 v to 220 v. - #20 [atracc], 13-12-24 10:34Most of the new Accuphase comes with 230V (Econ mode for idle timing more than 120 min). I read this in Accuphase.com
Properly, the old model only comes with 100V, 120V, 220V and 240V.
Any Ching with further comment. - #19 [FWFW], 13-12-24 09:40I can't find 230V in both DP-80 and DC-81.
- #18 [atracc], 13-12-24 01:32可惜,我部經典已經賣了,點解唔見230V ?
最後修改時間: 2013-12-24 01:35:22 - #17 [atracc], 13-12-24 01:21ching, p300v 跟你幅圗一模一㨾,可否起所有jumper再照一幅,我想再細看清楚230v and 220v setting, 小弟可能要到230v 地區比較長的日子,我相信新機報局都差不多,這圖肯定給金仔迷得益不少 thank you
最後修改時間: 2013-12-24 01:23:08 - #16 [254mm], 13-12-22 12:08都費事拖牛啦，仲有一下不小心就燒牛了
- #15 [fwfw], 13-12-22 12:00254mm師兄，
兩部都完成了，多謝你先！
但我發現100V同220V分聲別不大
註：本身用1KV凱韻隔離降壓牛 - #14 [254mm], 13-12-22 09:22這些插是相通的, 你小心看便知了
- #13 [fwfw], 13-12-22 01:57高空圖
- #12 [fwfw], 13-12-22 01:53各位師兄，因小弟影不到張label,圖是DP-80,我見上排五個插頭，下排五個插頭，如果上下排都要插的，我可根據圖示駁到，但如果只是插一個的，應該插上排定下排？還是上下排通的，任選其一？
例如：
跟據張label所示，啡色那條要駁去最右手那排，但應該駁去右上定右下那個插呢？因為label無顯示
謝謝各位師兄！
- #11 [fwfw], 13-12-22 00:33小弟膽粗粗跟住圖示改，成功了，多謝各位！現在到DP-80轉盤了，希望可以攪掂！
Thanks all big brother ! - #10 [lnchu], 13-12-22 00:32只要理解现在100V時,對一對label 100v表上線顏色及位置.再看一看label 220v表把所有線改動.因雙牛,左右顏色要一樣.
- #9 [254mm], 13-12-22 00:18上述 example, 講多少少
100 V = 0-100V
0-100V 同相 並聯
200 V = 0-100V-0-100V 順序串連
現在明未 ? therefore 要 set 220 V, 就要有兩組 110 V 0r 100V + 120V, you should have a better picture now!! - #8 [254mm], 13-12-22 00:11都算你明我講乜, 是要靠 label 上的標示才知怎駁, 你盡量看有冇兩組 110 V 的標示, 如有就應改到
- 下一頁 (1 of 2)
- 返回 ...
請教高手Accuphase機內轉電壓接駁方法？
謝謝。